Kawi2strokes.com Forum

Enthusiasts from around the world dedicated to the preservation and ritual flogging of the infamous Kawasaki 2-stroke Triples
It is currently Thu May 01, 2025 9:44 pm

Board index » Our legendary Kawasaki Triples » Triples Racing, and factory race bikes

All times are UTC - 5 hours




Post new topic Reply to topic  Page 1 of 2
  [ 20 posts ]  Go to page 1, 2  Next
  Print view Previous topic | Next topic 
Author Message
sawracer
 Post subject: H2 clutch slipping
PostPosted: Wed May 09, 2012 3:14 pm 

Joined: Mon Nov 21, 2011 12:34 pm
Posts: 676
Location: orange CA
Can I cure my clutch slipping blues with a simple spring upgrade? I called redline and haven't heard back from him. The clutch looked fine when apart, so I'm guessing it's the extra hp.
Top
 Profile  
 
mraxl
 Post subject: Re: H2 clutch slipping
PostPosted: Wed May 09, 2012 3:37 pm 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:36 am
Posts: 2714
Location: Dandridge, TN, USA
There are a couple of things to look at before you jump to new springs, if you haven't already...
- type of oil
- plate thickness
- pressure plate orientation
- actuator adjustment
- scuff steel plates

_________________
Answers are here: http://kawatriple.com/
Top
 Profile  
 
Hal
 Post subject: Re: H2 clutch slipping
PostPosted: Thu May 10, 2012 3:09 am 
User avatar

Joined: Thu Jun 09, 2011 12:52 am
Posts: 360
Location: London, UK
And also a very common one is if the steels have been overheated they can warp and drastically reduce the mating face area, so check them for flatness too.
Top
 Profile  
 
sawracer
 Post subject: Re: H2 clutch slipping
PostPosted: Mon May 14, 2012 3:17 pm 

Joined: Mon Nov 21, 2011 12:34 pm
Posts: 676
Location: orange CA
Ill get on this when it comes apart to replace that side of the engine :-(
Top
 Profile  
 
BarryB
 Post subject: Re: H2 clutch slipping
PostPosted: Mon May 14, 2012 5:20 pm 
User avatar

Joined: Wed Jun 08, 2011 10:23 pm
Posts: 3850
Location: Colorado Springs, CO. USA
Oil made the difference for me - went to Gearsaver 80 - problem solved.

_________________
This is true. Where I grew up the hills were so steep and long, when your ball rolled down the hill you just said "screw it"...
Top
 Profile  
 
docrick
 Post subject: Re: H2 clutch slipping
PostPosted: Fri Aug 24, 2012 7:31 am 

Joined: Thu Jun 23, 2011 1:04 pm
Posts: 213
Location: Southern New Jersey
mraxl wrote:
There are a couple of things to look at before you jump to new springs, if you haven't already...
- type of oil
- plate thickness
- pressure plate orientation

MRAXL.....Can you please elaborate on pressure plate orientation? Are you referring to the dot being lined up? just trying to expand my knowledge base a little... :clap:

- actuator adjustment
- scuff steel plates
Top
 Profile  
 
mraxl
 Post subject: Re: H2 clutch slipping
PostPosted: Fri Aug 24, 2012 7:57 am 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:36 am
Posts: 2714
Location: Dandridge, TN, USA
Yes, as below
Image

_________________
Answers are here: http://kawatriple.com/
Top
 Profile  
 
Steve
 Post subject: Re: H2 clutch slipping
PostPosted: Fri Aug 24, 2012 8:57 am 
User avatar

Joined: Sat Mar 10, 2012 8:12 am
Posts: 710
BarryB wrote:
Oil made the difference for me - went to Gearsaver 80 - problem solved.


That heavy of an oil in the transmission can cost some horsepower.

Not really an issue on the street though......

_________________
steve
Top
 Profile  
 
Zambia
 Post subject: Re: H2 clutch slipping
PostPosted: Fri Aug 24, 2012 8:58 am 
User avatar

Joined: Wed Jun 08, 2011 10:08 pm
Posts: 1901
Location: Campbellville Ontario
motohorseman wrote:
BarryB wrote:
Oil made the difference for me - went to Gearsaver 80 - problem solved.


That heavy of an oil in the transmission can cost some horsepower.

Not really an issue on the street though......


80 weight gear oil is not heavy.
Top
 Profile  
 
Gerrit
 Post subject: Re: H2 clutch slipping
PostPosted: Wed Jun 05, 2013 2:17 pm 

Joined: Fri Aug 19, 2011 3:15 am
Posts: 224
Location: Kingdom of the Netherlands
I had a severe clutch slip problem over 5,000 rpm with my green 73 H2-A years ago (Leo knows which bike). I simply chucked the steel plates out, fitted seven H1 steel plates instead with an extra H2 friction plate and problem solved!
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 2
  [ 20 posts ]  Go to page 1, 2  Next

Board index » Our legendary Kawasaki Triples » Triples Racing, and factory race bikes

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group