| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum http://www.kawi2strokes.com/forum/viewtopic.php?f=27&t=5331 |
Page 1 of 1 |
| Author: | z1 zonly [ Wed Jan 02, 2013 9:06 pm ] |
| Post subject: | WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
Looking to trade a working (diaphragm works, leaky around knob) stock late H1 petcock for a PMC, Pingel, or other petcock that I can thread on and go with. |
|
| Author: | m in sc [ Thu Jan 03, 2013 9:24 am ] |
| Post subject: | Re: WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
guess what? harley electra glide petcocks are vac operated and take same thread, just need to run a splitter for fuel as they are single outlet. im serious. or.... http://www.ebay.com/itm/PETCOCK-22-MM-C ... d1&vxp=mtr |
|
| Author: | Hawaii-Mike [ Fri Jan 04, 2013 4:55 am ] |
| Post subject: | Re: WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
Is that a Pingel? The price seems too low. Z1 Enterprises used to sell petcocks that looked like Pingels. I bought one for my KZ1000 and it started leaking after a few months. |
|
| Author: | m in sc [ Fri Jan 04, 2013 9:01 am ] |
| Post subject: | Re: WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
yeah, i had the same problem with one. i got harley one off ebay (knockoff) and its been fine. (on the S2) the h1 has a pingle. |
|
| Author: | Agent H2 [ Fri Jan 04, 2013 12:38 pm ] |
| Post subject: | Re: WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
Only one outlet? Do you foresee any problems with flow? Is there enough supply split three ways? |
|
| Author: | z1 zonly [ Fri Jan 04, 2013 3:26 pm ] |
| Post subject: | Re: WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
I just ordered a petcock, so, stock H1 petcock with good diaphragm for sale!s |
|
| Author: | Ja-Moo [ Fri Jan 04, 2013 4:08 pm ] |
| Post subject: | Re: WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
Agent H2 wrote: Only one outlet? Do you foresee any problems with flow? Is there enough supply split three ways? If it's a 1/4" it should be fine, That's what I use......... |
|
| Author: | m in sc [ Fri Jan 04, 2013 4:09 pm ] |
| Post subject: | Re: WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
only can flow as much as the hole in the 4 hole gasket. thats about 5-6 mm diameter if i am correct. so, no. funny people fit huge fuel lines but never look at eh true bottle neck, the petcock. Remember, at the carb, you are only usually flowing (max) through a 2mm a needle seat orifice. occasionally 3.0 but thats unusual for a street motor. |
|
| Author: | Ja-Moo [ Fri Jan 04, 2013 5:16 pm ] |
| Post subject: | Re: WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
no to what Mark? |
|
| Author: | m in sc [ Fri Jan 04, 2013 7:24 pm ] |
| Post subject: | Re: WTT H1 vacuum petcock for PMC/Pingel/other non-vacuum |
no, as in no problem. should work fine! |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|