Here it is. His is the best of all the aftermarket actuators.
http://www.gille-restauration.de
| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| H2 Clutch Release Mechanism http://www.kawi2strokes.com/forum/viewtopic.php?f=26&t=13519 |
Page 1 of 4 |
| Author: | Erle [ Wed Aug 15, 2018 5:27 pm ] |
| Post subject: | H2 Clutch Release Mechanism |
Hi. My H2 motor rebuild is just sitting, cause I can't find the proper Clutch Release Mechanism. I need the one for an H2-C. It has the "outer" half with the ball bearings, and the "inner" half with the "C" clip at the bottom of the gear. It's a beautiful rebuild going on, so the part needs to be in excellent condition please. Also, can't find the Neutral Switch, part #13151-012. Any help would be GREATLY appreciated. Thanks, Erle |
|
| Author: | Hawaii-Mike [ Wed Aug 15, 2018 8:37 pm ] |
| Post subject: | Re: H2 Clutch Release Mechanism |
Here's a brand new neutral switch: https://www.ebay.com/itm/NOS-OEM-13151- ... SwImRYCRl~ |
|
| Author: | Ja-Moo [ Wed Aug 15, 2018 10:18 pm ] |
| Post subject: | Re: H2 Clutch Release Mechanism |
Ralf Gillie makes a far superior replacement. I can get you his information if you so desire. |
|
| Author: | Erle [ Thu Aug 16, 2018 4:29 pm ] |
| Post subject: | Re: H2 Clutch Release Mechanism |
Thanks Mike, but the 13151-014 lists for the 250-400's. The H2 needs 13151-012. Apparently, they're not the same. They sure do LOOK the same??? |
|
| Author: | Erle [ Thu Aug 16, 2018 4:35 pm ] |
| Post subject: | Re: H2 Clutch Release Mechanism |
Thanks much Ja-Moo. If it's different from THIS---- https://www.ebay.com/itm/H2-H1-KH-Brass ... SwGOxW~qTA ----then I would definitely like a link, or more info. Thanks again. |
|
| Author: | Hawaii-Mike [ Thu Aug 16, 2018 7:04 pm ] |
| Post subject: | Re: H2 Clutch Release Mechanism |
I have an H2 and a KH400. I just took a look at them and they look the same, though I can't say for certain. Here's a used H2 switch: https://www.ebay.com/itm/KAWASAKI-H2-75 ... SwUf5bZLkv |
|
| Author: | n2trips [ Thu Aug 16, 2018 8:29 pm ] |
| Post subject: | Re: H2 Clutch Release Mechanism |
https://www.ebay.com/itm/Kawasaki-H2-H1 ... SwiSJbdgqD |
|
| Author: | Ja-Moo [ Thu Aug 16, 2018 10:53 pm ] |
| Post subject: | Re: H2 Clutch Release Mechanism |
Erle wrote: Thanks much Ja-Moo. If it's different from THIS---- https://www.ebay.com/itm/H2-H1-KH-Brass ... SwGOxW~qTA ----then I would definitely like a link, or more info. Thanks again. It is different, I will get you a E mail. |
|
| Author: | Ja-Moo [ Thu Aug 16, 2018 10:59 pm ] |
| Post subject: | Re: H2 Clutch Release Mechanism |
Here it is. His is the best of all the aftermarket actuators. http://www.gille-restauration.de |
|
| Author: | don k [ Fri Aug 17, 2018 9:11 pm ] |
| Post subject: | Re: H2 Clutch Release Mechanism |
Ja-Moo Ralf's has a spline similar to the Sytec, probably similar travel. Z1 sells one where the spline is similar to the ball bearing Kawasaki release. More travel, but more pull tension. https://www.ebay.com/itm/H2-H1-KH-Brass ... SwGOxW~qTA MachVmotors has 2 ball bearing units listed on fleebay, one new one used. All better than the original nylon Kaw units. Don |
|
| Page 1 of 4 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|