Just bumping it up there.I know they're are not that common.Can you guys with early H1's ones afford to part with a spare.
Have cash or some h1/h2 parts to swap.
Here's a pic from Mraxls' resources
http://3cyl.com/mraxl/partid/oillines/oillines.htm
| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| early H1 RH/oil pipe 16134-006 http://www.kawi2strokes.com/forum/viewtopic.php?f=26&t=10929 |
Page 1 of 2 |
| Author: | tone [ Wed Sep 09, 2015 4:42 pm ] |
| Post subject: | early H1 RH/oil pipe 16134-006 |
Hey Guys, Looking for some help to get this oil pipe.16134-006 Have been looking for months but no cigar. The engine side brass junction is slightly higher than the later ones, which also uses a different banjo-bolt.I don't mind a good used one.Thanks |
|
| Author: | tone [ Thu Sep 24, 2015 10:30 pm ] |
| Post subject: | Re: early H1 RH/oil pipe 16134-006 |
Just bumping it up there.I know they're are not that common.Can you guys with early H1's ones afford to part with a spare. Have cash or some h1/h2 parts to swap. Here's a pic from Mraxls' resources http://3cyl.com/mraxl/partid/oillines/oillines.htm
|
|
| Author: | RODH2 [ Fri Sep 25, 2015 12:18 am ] |
| Post subject: | Re: early H1 RH/oil pipe 16134-006 |
What does the wider brass fitting measure, Tone, I have a set of '70 cases with a few oil lines, and fittings....... may not be 'early' enough??? |
|
| Author: | RODH2 [ Fri Sep 25, 2015 12:23 am ] |
| Post subject: | Re: early H1 RH/oil pipe 16134-006 |
...just had a look, I think the fittings I have are 'later' ...... |
|
| Author: | tone [ Fri Sep 25, 2015 1:15 am ] |
| Post subject: | Re: early H1 RH/oil pipe 16134-006 |
Hey thanks for looking Rod,the brass fitting is 12mm as opposed to the later ones,I think 7mm. The early ones take a different banjo bolt, 92001-061. I don't think there is a bulletin about it and only RB would probably know when they changed it and who?  Maybe Tuner knows why. Thanks again Rod,tone 
|
|
| Author: | kawi3cyl [ Sun Sep 27, 2015 1:25 pm ] |
| Post subject: | Re: early H1 RH/oil pipe 16134-006 |
Tone, good to see you're still at it! Hope all is well. Please compare to yours to be sure this one is correct. If so, $25 plus shipping. I believe Priority Flat-Rate to you is $12.95, but let me actually put the particulars into the USPS online before I total it up, as I am not 100% on that and the USPS seems to raise int'l prices frequently. Let me know if you want it.   
|
|
| Author: | tone [ Sun Sep 27, 2015 4:17 pm ] |
| Post subject: | Re: early H1 RH/oil pipe 16134-006 |
Hey Darrin, Yes still at,I have had a few family issues....  but looking at getting some projects on the bench.That is the oil pipe pictured Darrin and thanks for looking into it for me.I'll pm my pay p@l address. Tone 
|
|
| Author: | ThreePipesSmokin [ Sun Sep 27, 2015 4:39 pm ] |
| Post subject: | Re: early H1 RH/oil pipe 16134-006 |
I would wait and try to find one without the air bubble, that's gonna cause you problems...   
|
|
| Author: | kawi3cyl [ Sun Sep 27, 2015 9:07 pm ] |
| Post subject: | Re: early H1 RH/oil pipe 16134-006 |
You're a regular Jerry Seinfeld!
|
|
| Author: | ThreePipesSmokin [ Mon Sep 28, 2015 6:32 am ] |
| Post subject: | Re: early H1 RH/oil pipe 16134-006 |
kawi3cyl wrote: You're a regular Jerry Seinfeld! ...not that there's anything wrong with that! 
|
|
| Page 1 of 2 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|