Large carb adapters for the H2.
32 to 39.5mm carbs. Set comes complete with aluminum manifolds, clamps, tubing and allen head bolts.
129.00 plus shipping
| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| New Product http://www.kawi2strokes.com/forum/viewtopic.php?f=25&t=12691 |
Page 1 of 1 |
| Author: | Ja-Moo [ Sat Apr 15, 2017 8:40 am ] |
| Post subject: | New Product |
Large carb adapters for the H2. 32 to 39.5mm carbs. Set comes complete with aluminum manifolds, clamps, tubing and allen head bolts. 129.00 plus shipping
|
|
| Author: | Hawaii-Mike [ Sat Apr 15, 2017 1:12 pm ] |
| Post subject: | Re: New Product |
Interesting, looks like they tilt the carbs up a bit. Is that for crankcase clearance? |
|
| Author: | Ja-Moo [ Sat Apr 15, 2017 1:28 pm ] |
| Post subject: | Re: New Product |
That and a straight shot down the port.
|
|
| Author: | 4 Dog knight [ Sat Apr 15, 2017 11:14 pm ] |
| Post subject: | Re: New Product |
John, Going that big on the carbs...do you get a kind of secondary Venturi effect as the mixture enters the smaller intake port? Are they designed to match a reed block or the cylinder. Appears to be the cylinder? Or do the reed blocks neutralize any of that potential? I gotta believe they have to taper down some to match the cylinders? Enquiring mind need to know! 4Dog |
|
| Author: | Ja-Moo [ Sun Apr 16, 2017 9:18 am ] |
| Post subject: | Re: New Product |
4 Dog knight wrote: John, Going that big on the carbs...do you get a kind of secondary Venturi effect as the mixture enters the smaller intake port? Are they designed to match a reed block or the cylinder. Appears to be the cylinder? Or do the reed blocks neutralize any of that potential? I gotta believe they have to taper down some to match the cylinders? Enquiring mind need to know! 4Dog Not really, as the intake port will be matched to the adapter. One plus (beside the straight shot intake) is it adds some intake length/area, this allows for a bit of ram effect from the intake flow, also changes the intake wave timing to the carb. These adapters are actually for the guys running piston port motors. I do have a Stage II reed conversion for the guys wanting big carbs and reeds.
|
|
| Author: | demus [ Sun Apr 16, 2017 4:24 pm ] |
| Post subject: | Re: New Product |
Would they hurt using them with your stage one kit? They look good, would make carb removal easier, with the 34's a guy has to do a bit of shaving on the carb bowls and I still have some trouble getting the left carb on and off. Having a straighter shot can't hurt. I have been thinking of making new spacers on the stage one kit, angled just a bit for these reasons . Maybe this is the answer I was looking for. 
|
|
| Author: | Ja-Moo [ Sun Apr 16, 2017 4:51 pm ] |
| Post subject: | Re: New Product |
I looked, won't work, too different. If you cut a bit off the top of the countershaft cover, the carb comes off much easier. |
|
| Author: | demus [ Sun Apr 16, 2017 6:58 pm ] |
| Post subject: | Re: New Product |
That's to bad... more of a looks thing for me, it looks strange in my mind when ever I look at the cylinders angle compared to carb angle. Looks like a good product
|
|
| Author: | Ja-Moo [ Sun Apr 16, 2017 7:34 pm ] |
| Post subject: | Re: New Product |
Thanks Joe! I'm not going to do another casting run for a while, but if you don't figure something out, I can probably modify a set in wax before casting.
|
|
| Author: | AER005 [ Mon Apr 17, 2017 12:10 am ] |
| Post subject: | Re: New Product |
I like your work , John you know how to get triples going , URs Al in Aus |
|
| Page 1 of 1 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|