The h1 I bought came with this monster on it.
| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| are there any crash bars/case protectors for the H1 http://www.kawi2strokes.com/forum/viewtopic.php?f=2&t=4651 |
Page 1 of 2 |
| Author: | two-stroke-brit [ Mon Oct 15, 2012 12:18 pm ] |
| Post subject: | are there any crash bars/case protectors for the H1 |
i saw some nice neat case protectors on a suzuki made by tarrozi are something like that. i have made a quick search but could not find the same sort of thing. TIA Mark |
|
| Author: | husson73 [ Mon Oct 15, 2012 12:25 pm ] |
| Post subject: | Re: are therev any crash bars/case protectors for the H1 |
some small one for 350 S2, 400 S3 or KH 400 could be modified unless you prefer the big one look like HD crash bar for H1. |
|
| Author: | oxford [ Mon Oct 15, 2012 12:39 pm ] |
| Post subject: | Re: are therev any crash bars/case protectors for the H1 |
The h1 I bought came with this monster on it.
|
|
| Author: | two-stroke-brit [ Mon Oct 15, 2012 12:41 pm ] |
| Post subject: | Re: are therev any crash bars/case protectors for the H1 |
I am looking for the smaller version , Everything I have seen is too big . About the size of your hand would be ideal . Maybe modifying is the way to go Thanks Husson for the input |
|
| Author: | Jim [ Mon Oct 15, 2012 1:28 pm ] |
| Post subject: | Re: are therev any crash bars/case protectors for the H1 |
Have you seen the sliders I made? They're 1.25" 6061 aluminum bar with 2 inch PVC caps pressed on the ends. A 1/2" bolt goes through the engine mounts into threaded holes in the aluminum bar. http://www.kawi2strokes.com/forum/viewtopic.php?f=2&t=3323&p=32583&hilit=sliders#p32583 |
|
| Author: | two-stroke-brit [ Mon Oct 15, 2012 1:43 pm ] |
| Post subject: | Re: are therev any crash bars/case protectors for the H1 |
Hi jim, I remember you made those now. Do you think that it might bend where you mount the at the triangle . A lot of bending force concentrated inline spot. I think two or three mounting points would spread the load more evenly . I might look into some 1/2 or 5/8 tit or stainless bar or tube and fab some up. Depends on what I can find Cheers mark |
|
| Author: | mraxl [ Mon Oct 15, 2012 1:56 pm ] |
| Post subject: | Re: are therev any crash bars/case protectors for the H1 |
I have one for an S3, like new, that was on a bike I bought. It mounts to the horn mount on top and the unused frame tabs at the bottom. |
|
| Author: | Jim [ Mon Oct 15, 2012 2:33 pm ] |
| Post subject: | Re: are therev any crash bars/case protectors for the H1 |
two-stroke-brit wrote: Hi jim, I remember you made those now. Do you think that it might bend where you mount the at the triangle . A lot of bending force concentrated inline spot. If it hits a solid object like a curb, something will bend or break, of course. The idea of the sliders is to protect the engine parts, maybe the chambers, etc., in a sliding crash. I think 1.25" solid 6061-T6 will not bend in a sliding situation, and the little triangular engine mounts are pretty tough. They're also easy to make if the originals get messed up. I'm not trying to talk you into them, however... too much responsibility. 
|
|
| Author: | Walms [ Mon Oct 15, 2012 3:27 pm ] |
| Post subject: | Re: are therev any crash bars/case protectors for the H1 |
Get with the program Jim!!! Sliders are supposed to be made of magnesium to insure an impressive slide and to ignite the gas that has spilled. |
|
| Author: | two-stroke-brit [ Mon Oct 15, 2012 3:53 pm ] |
| Post subject: | Re: are therev any crash bars/case protectors for the H1 |
i get it jim , more sliding/garrage fall over protection. 
|
|
| Page 1 of 2 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|