That would make for a nice build thread on that!
| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| case reeded S series? http://www.kawi2strokes.com/forum/viewtopic.php?f=2&t=4576 |
Page 1 of 2 |
| Author: | m in sc [ Sat Oct 06, 2012 7:04 am ] |
| Post subject: | case reeded S series? |
has anybody done this on an S series motor? if so, pics please. I know H1 and H2s have been done. not interested in that. |
|
| Author: | Walms [ Sat Oct 06, 2012 8:54 am ] |
| Post subject: | Re: case reeded S series? |
That would make for a nice build thread on that!
|
|
| Author: | kawi3cyl [ Sat Oct 06, 2012 6:34 pm ] |
| Post subject: | Re: case reeded S series? |
If I am not mistaken, I believe jhenise from the old board is/was working extensively on such an endeavor for his S2. I can't say how to contact him though...? |
|
| Author: | Ja-Moo [ Sat Oct 06, 2012 7:55 pm ] |
| Post subject: | Re: case reeded S series? |
kawi3cyl wrote: If I am not mistaken, I believe jhenise from the old board is/was working extensively on such an endeavor for his S2. I can't say how to contact him though...? His is a port reed...... |
|
| Author: | m in sc [ Sat Oct 06, 2012 8:28 pm ] |
| Post subject: | Re: case reeded S series? |
was wonderding if theres enough room there to do it... hm. need to measure some stuff methinks |
|
| Author: | gary c [ Sun Oct 07, 2012 1:52 am ] |
| Post subject: | Re: case reeded S series? |
thers enough room if you use smaller reed boxes  i have rode henrys [magee] case reed h2 several times and its a great piece of kit good luck with the project ask henry about the drawbacks /problems mainly warping cases when welding it might save you a lot of grief in the long run |
|
| Author: | magee [ Sun Oct 07, 2012 7:10 pm ] |
| Post subject: | Re: case reeded S series? |
i only did mine as it was more of a challange. It runs realy well just as Bill Baxter, Gary Clark and the NIpper can atest to. I do have a bit of a problem with carburation at high revs due t the connecting rods getting in the way of the inlet charge, Bill recons i only get 100 plusHP at te rear wheel. good luck, let me know if i can help. |
|
| Author: | Ja-Moo [ Sun Oct 07, 2012 10:09 pm ] |
| Post subject: | Re: case reeded S series? |
You made your magic 100! 
|
|
| Author: | husson73 [ Mon Oct 08, 2012 3:33 am ] |
| Post subject: | Re: case reeded S series? |
UK guys have some 
|
|
| Author: | m in sc [ Mon Oct 08, 2012 12:30 pm ] |
| Post subject: | Re: case reeded S series? |
magee, thats what i was wondering. the rod and flywheels are right there and will cause all sorts of weird turbulence. considering the s seires is so small anyway, i figure some small reeds would def be the way to go. This is for an S2 BTW. still not sure whether to just do a convetional reed mod(much easier IMHO) or case reed or try to get the bolt-on adapter i designed made. or just leave it well enough alone ......  ...decisions. so, no one has done a case reeded s1, s2, or 400? 
|
|
| Page 1 of 2 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|