| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| Squish Heads from Moo http://www.kawi2strokes.com/forum/viewtopic.php?f=16&t=9940 |
Page 1 of 3 |
| Author: | BBP [ Sat Feb 07, 2015 6:56 pm ] |
| Post subject: | Squish Heads from Moo |
These are Really Cool John........another "Moodified" bike.........I thought he just cut a new squish band........but the whole head is re-engineered........and opens up around the spark plug........and some port work........Glass Beading by Tim Steele.........Good Work  THX Phil     
|
|
| Author: | Ja-Moo [ Sat Feb 07, 2015 7:21 pm ] |
| Post subject: | Re: Squish Heads from Moo |
Thanks Phil! That is a nice package........ 
|
|
| Author: | Tim Steele [ Sat Feb 07, 2015 11:48 pm ] |
| Post subject: | Re: Squish Heads from Moo |
MOO You scare me when you talk about Phil's package... 
|
|
| Author: | Ja-Moo [ Sun Feb 08, 2015 1:07 am ] |
| Post subject: | Re: Squish Heads from Moo |
Well, you blasted his heads........ 
|
|
| Author: | kwacka.karl [ Sun Feb 08, 2015 9:42 am ] |
| Post subject: | Re: Squish Heads from Moo |
Nice job on the heads are they around the same cc and are the barrels late ones with after market jets in the oil galleys....kwacka karl....ozz 
|
|
| Author: | Tim Steele [ Sun Feb 08, 2015 10:20 am ] |
| Post subject: | Re: Squish Heads from Moo |
Indeed I did and he liked it... |
|
| Author: | Ja-Moo [ Sun Feb 08, 2015 2:42 pm ] |
| Post subject: | Re: Squish Heads from Moo |
kwacka.karl wrote: Nice job on the heads are they around the same cc and are the barrels late ones with after market jets in the oil galleys....kwacka karl....ozz The head CC's are adjusted for the ex height, and I think you are correct on the late cylinders. |
|
| Author: | BBP [ Sun Feb 08, 2015 10:40 pm ] |
| Post subject: | Re: Squish Heads from Moo |
Quote: You scare me when you talk about Phil's package... Tim.....my Package has been the subject of many a conversation for a long time now......thanks dad I am used to it, after hanging out with my Buddies at the shop up the street, nothing is too offending. Tim, you handled the "Package" also.....so watch out  THX Phil
|
|
| Author: | BBP [ Sun Feb 08, 2015 10:47 pm ] |
| Post subject: | Re: Squish Heads from Moo |
kwacka.......they are late style cylindrers.....H2B.........Moo's machinist bored it for first over Wossners........Moo did the transfer cutout to match the pistons and a stage 1 port........it was already decked........then I drilled partially just enough to fit a 30 mikuni pilot jet (after cutting the jet down flush before installing).......screwed it in with some red loktite.........used copper base and head gaskets from Lani at coppergaskets.com ......then used the Darth 72/73 oil lines and pump......lot less smoke and a nice Boost in HP with chambers and VM34's THX Phil
|
|
| Author: | BBP [ Mon Feb 09, 2015 8:23 pm ] |
| Post subject: | Re: Squish Heads from Moo |
John I borrowed a compression tester from my buddy Doug........he has four of them........but some don't read correctly........one of them showed 153lbs before the new pistons and squish heads........(I could not remember which one I used) then the second one that was close.........some old 60's "Hawk" guage (I do remember it read 150)........it only reads in 10lb increments and you hear it click at each 10lbs..........each cylinder hit 150 lbs first kick and stayed there.........so it's somewhere between 150 and 160 He is going to buy a high quality set........I will re-check it when Doug gets the new one.......WFO and warmed up THX Phil
|
|
| Page 1 of 3 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|