Is this set up for mounting , hanging the lower off the upper OK??? Or should I add a helper bracket from the lower all the way back to the frame on the backside ??
Untitled by Joe Herriges, on Flickr
| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| Goofing around with intake track/reeds http://www.kawi2strokes.com/forum/viewtopic.php?f=16&t=13151 |
Page 7 of 11 |
| Author: | demus [ Mon Apr 30, 2018 3:34 pm ] |
| Post subject: | Re: Goofing around with intake track/reeds |
H2RTuner wrote: . Just remember, this is a hobby, and....FUN (even if it frustrates the daylights out of you in the beginning! THAT is the truth...one must remember theses really are just for FUN! And DGA can't speak for anyone but myself but thats why I am here, to get advice and maybe, just maybe, help a little. Remember the old days where getting info or parts or anything was the biggest challenge , now its the opposite need to "wade" through all the info. I actually trust most triple guys a lot, alway good helpful advice. |
|
| Author: | Jim [ Sat May 05, 2018 8:28 am ] |
| Post subject: | Re: Goofing around with intake track/reeds |
I extended this offer to Walms a while back too... email or phone me if you want some tips. I can't promise they'll help, but they might. The phone might be better. |
|
| Author: | demus [ Sat May 05, 2018 11:24 am ] |
| Post subject: | Re: Goofing around with intake track/reeds |
Thanks Jim. Might take you up on it , although I just finished the last pipe last night just need to stingers , cans and mounting tabs |
|
| Author: | demus [ Fri May 11, 2018 7:07 am ] |
| Post subject: | Re: Goofing around with intake track/reeds/exhaust |
Is this set up for mounting , hanging the lower off the upper OK??? Or should I add a helper bracket from the lower all the way back to the frame on the backside ?? Untitled by Joe Herriges, on Flickr
|
|
| Author: | Ja-Moo [ Fri May 11, 2018 9:28 am ] |
| Post subject: | Re: Goofing around with intake track/reeds |
Looks good to me. 
|
|
| Author: | Hawaii-Mike [ Fri May 11, 2018 11:53 am ] |
| Post subject: | Re: Goofing around with intake track/reeds |
I think that's how Lomas pipes mount, one connects to the other. |
|
| Author: | jyrgNorway [ Fri May 11, 2018 5:00 pm ] |
| Post subject: | Re: Goofing around with intake track/reeds |
Jollymoto as well. Looking good Joe! |
|
| Author: | demus [ Sat May 12, 2018 6:27 am ] |
| Post subject: | Re: Goofing around with intake track/reeds |
Thanks for the feed back! Im so close to done and now the next couple days are shot and I will only have 1 night next week to work on it and next weekend is out too!!! I really should tell everyone at work I have appointments all day monday so dont call me unless its an emergency and leave work about 10am after everyone is set up and everyone is working and finish this thing… I am the boss, thats what they say anyway, although it sure dont feel like it most days! I think that might have to be my plan, it could work  
|
|
| Author: | Ja-Moo [ Sat May 12, 2018 10:49 am ] |
| Post subject: | Re: Goofing around with intake track/reeds |
DO IT!
|
|
| Author: | demus [ Tue Jun 05, 2018 6:57 am ] |
| Post subject: | Re: Goofing around with intake track/reeds |
Some may have seen I posted the first start with the new intakes on and the new exhaust in Pic and Video The Intake rubbers are the Harley compensator boots, which I immediately stole the idea from soflh2b after he posted how he did it. I am having some carb vibration with the new boots the boots are not as ridged as the original H2 boots so I connected the carbs with a piece of threaded rod along the top to hold them together. The vibration does not appear to affect the carbs whie driving at least I haven't noticed yet on the short runs I have taken on it so far. Besides foaming the fuel and possible over flow if the floats bounce to much I am imagining some serious wear issues at the jet needle, the seat, the float and the float tangs…. I do have the vm's with the separate floats so I imagine that helps a bit as far as fuel height. I have some thoughts but am wondering how much is too much? The Ram Air filters are flopping more than the carb, I will be taking it for a longer run tonight to start to sort through the jetting. Take a look at the video and watch the carbs, I know the quality sucks. https://www.youtube.com/watch?v=LljOpPrtWTg |
|
| Page 7 of 11 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|