Kawi2strokes.com Forum

Enthusiasts from around the world dedicated to the preservation and ritual flogging of the infamous Kawasaki 2-stroke Triples
It is currently Thu Mar 28, 2024 5:01 am

All times are UTC - 5 hours




Post new topic Reply to topic  [ 8 posts ] 
Author Message
PostPosted: Tue Dec 02, 2014 7:42 am 
User avatar

Joined: Tue Aug 21, 2012 5:01 am
Posts: 277
Location: Brownsburg IN
The 2 collars on the S1 transmission that the end needle bearing rides in has an oil slot/groove on one side. Cant remember and tough to get a good pic of it, does that oil slot/groove face in toward the tranny or out toward the side covers? Thanks,


Top
 Profile  
 
PostPosted: Tue Dec 02, 2014 11:23 am 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:37 am
Posts: 10460
Location: Rio Rancho, New Mexico
It doesn't matter as much as the hole is offset so it changes the shim stack clearance. That is way more important......

_________________
Twist the throttle, tilt the horizon, and have a great time. What triples are all about...........


Top
 Profile  
 
PostPosted: Tue Dec 02, 2014 11:42 am 

Joined: Thu Jun 09, 2011 2:00 am
Posts: 1010
Location: Southern Ontario, Canada
Slots in bearing sleeves referred are to enhance oiling of the thrust washers, hence are normally installed towards gears.
J


Top
 Profile  
 
PostPosted: Tue Dec 02, 2014 3:42 pm 
User avatar

Joined: Tue Aug 21, 2012 5:01 am
Posts: 277
Location: Brownsburg IN
Looney Cylinders wrote:
Slots in bearing sleeves referred are to enhance oiling of the thrust washers, hence are normally installed towards gears.
J

ja-moo, the locating hole for the dowel pin looks to be centered in the collar.
J- facing the gears would mean towards the inside of the transmission towards the center? that is what I thought it would make sense for it to be I just can't remember. Thanks guys


Top
 Profile  
 
PostPosted: Tue Dec 02, 2014 3:50 pm 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:36 am
Posts: 2691
Location: Dandridge, TN, USA
Image

_________________
Answers are here: http://kawatriple.com/


Top
 Profile  
 
PostPosted: Tue Dec 02, 2014 4:21 pm 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:37 am
Posts: 10460
Location: Rio Rancho, New Mexico
I would measure, as I have not seen one with the hole centered. It is just something to look out for, as you don't want to start having trans problems. There is oil splashing around on either side anyway.

_________________
Twist the throttle, tilt the horizon, and have a great time. What triples are all about...........


Top
 Profile  
 
PostPosted: Tue Dec 02, 2014 9:00 pm 
User avatar

Joined: Tue Aug 21, 2012 5:01 am
Posts: 277
Location: Brownsburg IN
mraxl wrote:
Image

Ding ding ding!!! There is the pic I needed!!! Thanks!!!!


Top
 Profile  
 
PostPosted: Tue Dec 02, 2014 9:45 pm 
User avatar

Joined: Wed Jun 08, 2011 10:41 pm
Posts: 3489
Location: Mount Vision, NY
When in doubt, Dale will bail ya out.....
The resource pages are invaluable to say the least.

_________________
Bad decisions make the best stories.



Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 8 posts ] 

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
cron
Powered by phpBB® Forum Software © phpBB Group