Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
When converting late H2 cases to a 3 line early pump http://www.kawi2strokes.com/forum/viewtopic.php?f=14&t=8516 |
Page 1 of 3 |
Author: | Ja-Moo [ Sat May 24, 2014 10:25 pm ] |
Post subject: | When converting late H2 cases to a 3 line early pump |
I'm beginning to put my 750 motor together, and did the drill mod for the oil holes to the cylinder base. I didn't do a lot of "homework" on the mod, and just drilled the holes. Well, as Murphy had some free time, he decided to stop by on this one. The holes need to break through to the main oil feed holes in the cases near the top, above where the threads start. This is the "chamber" that feeds the oil to the port. I had 2 that broke through in the threaded area, which caused a major headache to fix. so just be careful..... |
Author: | Jim [ Sat May 24, 2014 10:46 pm ] |
Post subject: | Re: When converting late H2 cases to a 3 line early pump |
https://www.youtube.com/watch?v=rX7wtNOkuHo& |
Author: | Ja-Moo [ Sat May 24, 2014 10:51 pm ] |
Post subject: | Re: When converting late H2 cases to a 3 line early pump |
You know how to perk a guy up Jim........ |
Author: | Jim [ Sat May 24, 2014 10:55 pm ] |
Post subject: | Re: When converting late H2 cases to a 3 line early pump |
Save that link, you'll need to send it back to me sometime soon, I'm sure. |
Author: | Ja-Moo [ Sat May 24, 2014 11:01 pm ] |
Post subject: | Re: When converting late H2 cases to a 3 line early pump |
I should have sent it when you mounted your rear pipe mount......... |
Author: | Jim [ Sat May 24, 2014 11:09 pm ] |
Post subject: | Re: When converting late H2 cases to a 3 line early pump |
Yes, and I would have laughed even harder than I did. |
Author: | scrambler73 [ Sun May 25, 2014 4:23 pm ] |
Post subject: | Re: When converting late H2 cases to a 3 line early pump |
another thing a guy has to be careful of is using a dull bit and "forcing" it through. This rookie mistake caused me to break off a bit, which is now a permanent resident in a set of cases. I was able to drill another hole just beside it (with a new, sharp bit), so crisis averted. |
Author: | Ja-Moo [ Sun May 25, 2014 5:51 pm ] |
Post subject: | Re: When converting late H2 cases to a 3 line early pump |
YEah, the long bits are brittle. I was "trying" to auger the holes upward, but just broke the bit. Luckily it just pushed out. |
Author: | 67lotus49 [ Mon May 26, 2014 10:54 am ] |
Post subject: | Re: When converting late H2 cases to a 3 line early pump |
What size drill should be used? I have a set of 74 cases that are set up for the Suzuki rubber mounts and I need to drill the oil passages. |
Author: | scrambler73 [ Mon May 26, 2014 2:53 pm ] |
Post subject: | Re: When converting late H2 cases to a 3 line early pump |
67lotus49 wrote: What size drill should be used? I have a set of 74 cases that are set up for the Suzuki rubber mounts and I need to drill the oil passages. I have a set of early H2 cases lying around and found a drill bit that just barely fit through the passage..... no clue what size it was though.. (some help I am eh?) |
Page 1 of 3 | All times are UTC - 5 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |