Kawi2strokes.com Forum

Enthusiasts from around the world dedicated to the preservation and ritual flogging of the infamous Kawasaki 2-stroke Triples
It is currently Thu Oct 31, 2024 6:48 pm

All times are UTC - 5 hours




Post new topic Reply to topic  [ 14 posts ]  Go to page 1, 2  Next
Author Message
 Post subject: Head gasket
PostPosted: Mon Jun 25, 2012 10:59 pm 

Joined: Sat May 26, 2012 5:09 pm
Posts: 89
Location: Covina California
I want to change the head on my right cylinder because it has a broken fin on it and when I bought the bike the guy gave me a good head that's not chipped. Can I reuse the same head gasket? Ive heard of annealing it with a torch is this OK or do I need to buy a new head gasket?
Also would I need to pull the cylinder to replace the base gasket? Thanks


Top
 Profile  
 
 Post subject: Re: Head gasket
PostPosted: Mon Jun 25, 2012 11:20 pm 
User avatar

Joined: Wed Jun 08, 2011 11:34 pm
Posts: 9928
Location: North Central NC
Yes, reuse the head gasket by annealing it. Heat it red hot all around with a propane torch or equivalent. You can quench it in water to flake off the black oxide, but it's not required.

No need to remove the cylinder or replace the base gasket.

_________________
If it surges, that's normal, upshift.


Top
 Profile  
 
 Post subject: Re: Head gasket
PostPosted: Mon Jun 25, 2012 11:23 pm 
User avatar

Joined: Fri Jun 22, 2012 6:17 pm
Posts: 48
Location: San Diego
You can anneal it and re-use it. I take it (the head gasket) and slightly bend one corner and hold it with a pair of needle nose pliers over the gas burner on the stove, let it get red hot (carefully not to get too hot as to melt it) the dip it in a bowl of water- its that easy.
you shouldn't have to replace the base gasket if you're careful when removing the head as not to break the seal between the cyl. and lower end.


Top
 Profile  
 
 Post subject: Re: Head gasket
PostPosted: Mon Jun 25, 2012 11:23 pm 

Joined: Sat May 26, 2012 5:09 pm
Posts: 89
Location: Covina California
Jim wrote:
Yes, reuse the head gasket by annealing it. Heat it red hot all around with a propane torch or equivalent. You can quench it in water to flake off the black oxide, but it's not required.

No need to remove the cylinder or replace the base gasket.

Thanks Jim!


Top
 Profile  
 
 Post subject: Re: Head gasket
PostPosted: Mon Jun 25, 2012 11:27 pm 
User avatar

Joined: Wed Jun 08, 2011 11:34 pm
Posts: 9928
Location: North Central NC
You're welcome dog.

Good to see you here, Grant.

_________________
If it surges, that's normal, upshift.


Top
 Profile  
 
 Post subject: Re: Head gasket
PostPosted: Mon Jun 25, 2012 11:30 pm 
User avatar

Joined: Fri Jun 22, 2012 6:17 pm
Posts: 48
Location: San Diego
Thanks jim,
you beat me to the answer but it took so long for me to write it (search and pecking) I had to post it anyways-DOH :banghead


Top
 Profile  
 
 Post subject: Re: Head gasket
PostPosted: Mon Jun 25, 2012 11:32 pm 

Joined: Thu Jun 09, 2011 2:00 am
Posts: 1010
Location: Southern Ontario, Canada
One other tip for you:
Use Permatex copper spray on your head gaskets. It helps prevent oil weeps.

J


Top
 Profile  
 
 Post subject: Re: Head gasket
PostPosted: Thu Aug 09, 2012 8:47 pm 
User avatar

Joined: Sun Jul 17, 2011 8:26 pm
Posts: 227
Location: Breese, IL
I am getting this oil weeping issue. First one cylinder (annealed and retorqued) and now another one,

Is this just an annoyance, or something to be concerned about?


Top
 Profile  
 
 Post subject: Re: Head gasket
PostPosted: Thu Aug 09, 2012 9:36 pm 
Site Admin
User avatar

Joined: Tue Jun 07, 2011 6:36 am
Posts: 2710
Location: Dandridge, TN, USA
If oil/fuel can leak out, then air can leak in, and that can be a problem.

_________________
Answers are here: http://kawatriple.com/


Top
 Profile  
 
 Post subject: Re: Head gasket
PostPosted: Thu Aug 09, 2012 9:54 pm 
User avatar

Joined: Wed Jun 08, 2011 11:34 pm
Posts: 9928
Location: North Central NC
I cut O-ring grooves in my heads for Viton O-rings. They don't leak, and I can remove and replace heads any time without buying gaskets, annealing, etc.. If you have a lathe...

_________________
If it surges, that's normal, upshift.


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 14 posts ]  Go to page 1, 2  Next

All times are UTC - 5 hours


Who is online

Users browsing this forum: Bing [Bot]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group