RODH2 wrote:
If it's a H2, VM34's will fit straight on the stock 'manifolds' and the Mikuni inlets are available too, which makes the carbs. fit without hitting the neutral switch........
neutral switch? what neutral switch?
| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| WTB 34mm Mikuni adapter plates ??? http://www.kawi2strokes.com/forum/viewtopic.php?f=14&t=14516 |
Page 1 of 2 |
| Author: | DRIIFT [ Sat Jul 17, 2021 10:18 pm ] |
| Post subject: | WTB 34mm Mikuni adapter plates ??? |
Can someone tell me where I can source 34mm adaptor plates for Mikuni 34mm carburetors? Thanks. Tim |
|
| Author: | Tim Steele [ Sun Jul 18, 2021 7:32 am ] |
| Post subject: | Re: WTB 34mm Mikuni adapter plates ??? |
https://www.ebay.com/itm/303135231169 |
|
| Author: | Jim [ Sun Jul 18, 2021 10:00 am ] |
| Post subject: | Re: WTB 34mm Mikuni adapter plates ??? |
Do you know who that is Tim? I'm just curious. |
|
| Author: | DRIIFT [ Sun Jul 18, 2021 10:01 am ] |
| Post subject: | Re: WTB 34mm Mikuni adapter plates ??? |
Would those also fit a 750? |
|
| Author: | Jim [ Sun Jul 18, 2021 10:20 am ] |
| Post subject: | Re: WTB 34mm Mikuni adapter plates ??? |
For a 750 you just need the right boots and matching of the intake runners to the boots. No adapters are required. |
|
| Author: | Tim Steele [ Sun Jul 18, 2021 3:58 pm ] |
| Post subject: | Re: WTB 34mm Mikuni adapter plates ??? |
No I don't Jim |
|
| Author: | RODH2 [ Sun Jul 18, 2021 9:33 pm ] |
| Post subject: | Re: WTB 34mm Mikuni adapter plates ??? |
If it's a H2, VM34's will fit straight on the stock 'manifolds' and the Mikuni inlets are available too, which makes the carbs. fit without hitting the neutral switch........ |
|
| Author: | Jim [ Sun Jul 18, 2021 10:09 pm ] |
| Post subject: | Re: WTB 34mm Mikuni adapter plates ??? |
RODH2 wrote: If it's a H2, VM34's will fit straight on the stock 'manifolds' and the Mikuni inlets are available too, which makes the carbs. fit without hitting the neutral switch........ It would be a pretty bad stretch to get VM34s on stock intake adapters. I'm sure it's been done many times, but I went with adapters that fit better than that. |
|
| Author: | RODH2 [ Mon Jul 19, 2021 1:16 am ] |
| Post subject: | Re: WTB 34mm Mikuni adapter plates ??? |
Oh, yes, Jim, they are not ideal, but will work if you have a "good" set of originals, not sure if anyone has! But the Mikuni inlets are available and work very well. (I went with the new Mikunis'). |
|
| Author: | BarryB [ Mon Jul 19, 2021 7:06 am ] |
| Post subject: | Re: WTB 34mm Mikuni adapter plates ??? |
RODH2 wrote: If it's a H2, VM34's will fit straight on the stock 'manifolds' and the Mikuni inlets are available too, which makes the carbs. fit without hitting the neutral switch........ neutral switch? what neutral switch?
|
|
| Page 1 of 2 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|