| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| exhaust gaskets http://www.kawi2strokes.com/forum/viewtopic.php?f=14&t=13461 |
Page 1 of 2 |
| Author: | Peter 750 [ Fri Jun 22, 2018 11:27 am ] |
| Post subject: | exhaust gaskets |
I used new, original exhaust gaskets, with some silicon liquid gasket on them, when fitting my Yesbike chambers on my H2A, but the left and right chambers are still leaking slightly at the cilinder, after every ride, there's a nice  smear of oil all over them...Do I just need more silicon, or is it OK to use two gaskets instead of one...?? And what about these gaskets I found on Ebay: https://www.ebay.nl/itm/ALLOY-EXHAUST-G ... 2749.l2648 
|
|
| Author: | Jim [ Fri Jun 22, 2018 11:28 am ] |
| Post subject: | Re: exhaust gaskets |
Is the leak between the head pipe and the adapter, or between the adapter and cylinder? I think you're saying it's leaking at the cylinder. I don't use gaskets there, I just clean the counterbore in the cylinder and the end of the adapter, put on a little silicone sealer, and bolt them together. |
|
| Author: | Peter 750 [ Fri Jun 22, 2018 11:30 am ] |
| Post subject: | Re: exhaust gaskets |
No adapter, just a headpipe, and it's leaking slightly between the headpipe and the cilinder... |
|
| Author: | Peter 750 [ Fri Jun 22, 2018 11:33 am ] |
| Post subject: | Re: exhaust gaskets |
|
|
| Author: | Jim [ Fri Jun 22, 2018 12:00 pm ] |
| Post subject: | Re: exhaust gaskets |
I'm not familiar with those chambers, other than from photos. Maybe the pipe is misaligned so its end doesn't fit squarely onto the mating surface of the cylinder. |
|
| Author: | demus [ Fri Jun 22, 2018 12:37 pm ] |
| Post subject: | Re: exhaust gaskets |
The Spec II's I had liked to leak like crazy with gaskets and silicone. Then I finally used a whole bunch of " The right stuff" silicone on the flange to the head, wiped it out nice and smooth in the port. A pain when you had to take them off and reseal them but it worked real well. I don't know what the difference is between the products, seemed more the same than different but it worked. I assume from the amount more than the product, I really layed it in heavy I was sick of the oil everywhere. I did it the same way with my new WTF's just because thats what I had done before to make it work, so far no spooge...that will change Im sure. |
|
| Author: | Peter 750 [ Fri Jun 22, 2018 2:42 pm ] |
| Post subject: | Re: exhaust gaskets |
Thanks. I'm going to use those Ebay "crush" gaskets with a lot of silicon sealer..... |
|
| Author: | Peter 750 [ Mon Jun 22, 2020 9:48 am ] |
| Post subject: | Re: exhaust gaskets |
Still leaking.... 
|
|
| Author: | ThatGPzGuy [ Mon Jun 22, 2020 3:29 pm ] |
| Post subject: | Re: exhaust gaskets |
Yep. Welcome to the club. I take a blue paper towel with some brake cleaner on it and wipe them down after every ride. Totally worth it for Jim's SS pipes. |
|
| Author: | Peter 750 [ Mon Jun 22, 2020 3:44 pm ] |
| Post subject: | Re: exhaust gaskets |
I'm gonna try one more time with some new silicon gasket that I just ordered. If it fails again, I'm forced to do the same, wiping the oil away with a cloth at every stop.... 
|
|
| Page 1 of 2 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|