Kawi2strokes.com Forum
http://www.kawi2strokes.com/forum/

H2B kickstart lever correct?
http://www.kawi2strokes.com/forum/viewtopic.php?f=14&t=13026
Page 2 of 3

Author:  soflah2b [ Thu Aug 24, 2017 11:14 am ]
Post subject:  Re: H2B kickstart lever correct?

I run a KZ750 kicker. Much better fit and clears expansion chambers.

Author:  Stev-o [ Thu Aug 24, 2017 5:00 pm ]
Post subject:  Re: H2B kickstart lever correct?

R.B. wrote:
[b]100% . . . It's just bent! My FBG bike was the same last ...

...replace it with an early KZ750 Twin kicker.



Thx for the suggestion

Author:  DGA [ Tue Aug 29, 2017 8:31 am ]
Post subject:  Re: H2B kickstart lever correct?

Will straighten mine, but saw this on Ebay:
Kawasaki H2 750 kick starter. Very Straight, they are usually bent. Nothing worse then your foot slipping off your Kickstarter and then hurting you leg. Good splines. Not loose. Good threads. Will need re-chroming. This one is the 72/74 H2 straight design as opposed to the later 74/75 curved H2 design. Have those also.

Suggesting the H2B and C have a curved one, is this correct?

Author:  Ja-Moo [ Tue Aug 29, 2017 9:18 am ]
Post subject:  Re: H2B kickstart lever correct?

I will say no, but not an expert. :wtf:

Author:  Jim [ Tue Aug 29, 2017 9:23 am ]
Post subject:  Re: H2B kickstart lever correct?

According to the resource site, all H2 levers are the same. http://www.kawatriple.com/partid/kicker/kicker.htm

Main page of the resource site: www.kawatriple.com

Author:  R.B. [ Thu Aug 31, 2017 7:22 am ]
Post subject:  Re: H2B kickstart lever correct?

They are ALL the same . . . But, I suspect some were cast from a different formulae of steel . . . .

Author:  H1FR [ Thu Aug 31, 2017 11:34 pm ]
Post subject:  Re: H2B kickstart lever correct?

OMG, I hope I am wrong, however there are 2 types. I will Post pictures if needed.

Probably a little off, the real sign that it is bent if the end tilts down and your foot could slide off. Very easy to straighten. Did 10 the other day, takes about one minute to do. A vise and a old empty fork tube all that is needed. There are 2 designs. With or without the curve. Later had the curve like yours.
Now it could be horribly tweaked also, which is beyond the one minute fix.

Author:  R.B. [ Fri Sep 01, 2017 7:59 am ]
Post subject:  Re: H2B kickstart lever correct?

H1FR wrote:
OMG, I hope I am wrong, however there are 2 types. I will Post pictures if needed.

.
Come on then . . I am always up for being corrected :thumbup:

Author:  H1FR [ Fri Sep 01, 2017 12:06 pm ]
Post subject:  Re: H2B kickstart lever correct?

Here are some that I have. Thicker, straight. Thinner with the curve.

Image


Image

Image

Thin, Curved 75 H2, it's actually a degrees or so bent, end should be in about a 1/3-1/2 inch
Image

72 thick and straight
Image

73 thick and straight
Image

Author:  joker [ Fri Sep 01, 2017 1:16 pm ]
Post subject:  Re: H2B kickstart lever correct?

I bought a NOS one off eBay years ago for my H2c, it hit my stock exhaust. Still in my parts pile.

Page 2 of 3 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/