upload pictureTank and chambers off. Needs fork seals, lower throttle cables and still deciding on chain and sprockets maybe this year maybe next....I have the fork seals and cables on hand...
| Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
| Phoenix Project 2017 Gap Prep begins http://www.kawi2strokes.com/forum/viewtopic.php?f=14&t=12522 |
Page 1 of 3 |
| Author: | Tim Steele [ Wed Feb 22, 2017 1:48 am ] |
| Post subject: | Phoenix Project 2017 Gap Prep begins |
| upload picture Tank and chambers off. Needs fork seals, lower throttle cables and still deciding on chain and sprockets maybe this year maybe next....I have the fork seals and cables on hand... |
|
| Author: | Jim [ Wed Feb 22, 2017 9:41 am ] |
| Post subject: | Re: Phoenix Project 2017 Gap Prep begins |
Have you tried cleaning the seals to see if that stops the leaking? You can make one from something like milk jug plastic, but here's what I'm talking about: https://www.amazon.com/Motion-Pro-Seal- ... B0039LDF4A |
|
| Author: | Tim Steele [ Wed Feb 22, 2017 12:41 pm ] |
| Post subject: | Re: Phoenix Project 2017 Gap Prep begins |
Yep I did and the are seeping... Got a set of new All Balls seals ready to go in. |
|
| Author: | Jim [ Wed Feb 22, 2017 12:58 pm ] |
| Post subject: | Re: Phoenix Project 2017 Gap Prep begins |
Cool. I haven't had any leak since I found out about the cleaning, so I haven't had a chance to try it. |
|
| Author: | Tim Steele [ Mon Feb 27, 2017 1:13 am ] |
| Post subject: | Re: Phoenix Project 2017 Gap Prep begins |
 screenshotSpent most of today building fence. But I was able to squeeze in a bit of triple wrenching....the plan for tomorrow after feeding the Baby Mommas is to continue the fork seal.job. |
|
| Author: | BarryB [ Mon Feb 27, 2017 9:47 am ] |
| Post subject: | Re: Phoenix Project 2017 Gap Prep begins |
These are fun things - good for you. Seals are easy so I don't think twice about doing them  These newer bikes -- not so easy 
|
|
| Author: | Tim Steele [ Mon Feb 27, 2017 10:48 am ] |
| Post subject: | Re: Phoenix Project 2017 Gap Prep begins |
The late model EX forks are the bushing type forks, so they are a little more hateful. You have to install the seals (I have the special tool) with the forks completely assembled. Hopefully I can get them done today. |
|
| Author: | Jim [ Mon Feb 27, 2017 11:04 am ] |
| Post subject: | Re: Phoenix Project 2017 Gap Prep begins |
I can't remember... are those Ninja 250 fork tubes and sliders? |
|
| Author: | BarryB [ Mon Feb 27, 2017 2:02 pm ] |
| Post subject: | Re: Phoenix Project 2017 Gap Prep begins |
Tim Steele wrote: The late model EX forks are the bushing type forks, so they are a little more hateful. You have to install the seals (I have the special tool) with the forks completely assembled. Hopefully I can get them done today. ahhh did not notice that. I bought a tool for my upside-down (modern-ish) forks - same deal. |
|
| Author: | Tim Steele [ Mon Feb 27, 2017 7:47 pm ] |
| Post subject: | Re: Phoenix Project 2017 Gap Prep begins |
[url=https://postimg.org/\900K /3myxw2pvj/]  [/url]how to take a screenshot on a pcApart and cleaned up. |
|
| Page 1 of 3 | All times are UTC - 5 hours |
| Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |
|