Kawi2strokes.com Forum

Enthusiasts from around the world dedicated to the preservation and ritual flogging of the infamous Kawasaki 2-stroke Triples
It is currently Wed May 07, 2025 4:08 am

Board index » Our legendary Kawasaki Triples » Restoring your old gal, all shiny like when she was new

All times are UTC - 5 hours




Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 
  Print view Previous topic | Next topic 
Author Message
ThreePipesSmokin
PostPosted: Thu Mar 22, 2012 11:55 am 
User avatar

Joined: Wed Jun 08, 2011 10:28 pm
Posts: 1572
Location: Tampa Bay Florida
What size are the Al crush washers on the oil pump lines? (at the check valves) I'm placing a McMaster-Carr order and they have 6, 8, 10, 12, 16, 18, 22 in packs of 50, 25 or 10 depending on size. I'm thinking 10/12 or 12/16? I can check when I get home but I'd like to place the order in time to ship today. BTW, I'm ordering 100 each of the "push" nuts (for side cover badges) in 4mm and 5mm so if anyone needs some let me know, I'll have plenty of spares! :wave:

_________________
We don't need no stinkin' Cams!
Top
 Profile  
 
RODH2
PostPosted: Thu Mar 22, 2012 7:24 pm 
User avatar

Joined: Thu Jun 09, 2011 7:03 am
Posts: 4612
Location: Milang, South Australia
Kawasaki lists the I.D. for the top washers as 10.5mm, and the I.D. for the bottom washers as 8.5mm. (H2 parts list).

_________________
"One day, your life will flash before your eyes. Make sure it's worth watching." : anon.
Top
 Profile  
 
ThreePipesSmokin
PostPosted: Thu Mar 22, 2012 7:39 pm 
User avatar

Joined: Wed Jun 08, 2011 10:28 pm
Posts: 1572
Location: Tampa Bay Florida
Thanks Rod, I just measured the bolt and got a hair under 8 & 10 so I think we have a winner! I'll be ordering 8mm & 10mm Al crush washers tomorrow, that should last me a while! :thumbup:

_________________
We don't need no stinkin' Cams!
Top
 Profile  
 
67lotus49
PostPosted: Thu Mar 22, 2012 9:39 pm 
User avatar

Joined: Thu Jun 23, 2011 2:26 pm
Posts: 1805
Location: Running Springs Ca
On the old forum the part numbers where listed somewhere from Mcmaster. I had luck at the local ace hardware store too, cheap and they don't leak.
Top
 Profile  
 
ThreePipesSmokin
PostPosted: Fri Mar 23, 2012 5:48 am 
User avatar

Joined: Wed Jun 08, 2011 10:28 pm
Posts: 1572
Location: Tampa Bay Florida
67lotus49 wrote:
On the old forum the part numbers where listed somewhere from Mcmaster. I had luck at the local ace hardware store too, cheap and they don't leak.

Old forum? HA! :e11 Here are the sizes you need for any triple, most of us use Stat-O-Seals for the 6mm (pump end). :thumbup:

Aluminum
M6: 97725A600 $8.65/50
M8: 97725A700 $8.65/50
M10: 97725A750 $9.62/50
Stat-O-Seals
M6: 93786A125 $14.80/10

(I tried to retain the original table format but it gets lost when posted) :(

_________________
We don't need no stinkin' Cams!
Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  Page 1 of 1
  [ 5 posts ] 

Board index » Our legendary Kawasaki Triples » Restoring your old gal, all shiny like when she was new

All times are UTC - 5 hours


Who is online

Users browsing this forum: No registered users

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
Powered by phpBB® Forum Software © phpBB Group