Kawi2strokes.com Forum http://www.kawi2strokes.com/forum/ |
|
I started to reassemble the H1D I'm restoring. It's done http://www.kawi2strokes.com/forum/viewtopic.php?f=13&t=12026 |
Page 1 of 4 |
Author: | GUTS [ Thu Aug 18, 2016 12:34 pm ] |
Post subject: | I started to reassemble the H1D I'm restoring. It's done |
This bike was not in the best of shape when I got it from Leroy. I had to resort to some cave-man tactics to get the cylinders off but all is good now. This is the first time I got the chrome back before I needed it and it only took three weeks to get it back! ![]() ![]() ![]() They always look nicer than they are when you start. ![]() Getting the cylinders off. ![]() I tried less invasive means but was thwarted. ![]() ![]() ![]() The crank was rusted in and had to be junked. It took a whole day to get the cased apart. ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() |
Author: | rngdng [ Thu Aug 18, 2016 1:47 pm ] |
Post subject: | Re: I started to reassemble the H1D I'm restoring |
That crank was toast. Nasty!!! Lane |
Author: | 900SL [ Thu Aug 18, 2016 1:59 pm ] |
Post subject: | Re: I started to reassemble the H1D I'm restoring |
Wow what a job. Looks like that engine has been sitting for quite some time! Love the looks of the H1D, and nice looking Zed in the background btw. Good luck ! |
Author: | Dewman418 [ Thu Aug 18, 2016 10:57 pm ] |
Post subject: | Re: I started to reassemble the H1D I'm restoring |
Looking good ![]() |
Author: | GUTS [ Sat Oct 08, 2016 8:50 pm ] |
Post subject: | Re: I started to reassemble the H1D I'm restoring. It's d |
I still have the fuel line clamps and the rear footrest pins to put on but I lost them in the garage. ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() The cables have all since been routed correctly. ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() I'm pretty sure the master cylinder cap is from a '72 unless the early '73s had this cap. I am getting the other style ready. ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() ![]() I am also still going to change out the seat cover, then it should be pretty good. |
Author: | Tim Steele [ Sat Oct 08, 2016 9:01 pm ] |
Post subject: | Re: I started to reassemble the H1D I'm restoring. It's done |
Beautiful work!!! |
Author: | 67lotus49 [ Sat Oct 08, 2016 9:57 pm ] |
Post subject: | Re: I started to reassemble the H1D I'm restoring. It's done |
Looks super nice ![]() |
Author: | husson73 [ Sun Oct 09, 2016 5:34 am ] |
Post subject: | Re: I started to reassemble the H1D I'm restoring. It's done |
Awesome job ![]() |
Author: | mraxl [ Sun Oct 09, 2016 7:24 am ] |
Post subject: | Re: I started to reassemble the H1D I'm restoring. It's done |
Super nice job! You are correct... the MCyl cap used is from earlier models. If you aren't aware... the dash light panel is a Japan only for later models. The H1D is unique to H1 & S for '73. Here is H1D panel: ![]() |
Author: | wavehog33 [ Sun Oct 09, 2016 7:48 am ] |
Post subject: | Re: I started to reassemble the H1D I'm restoring. It's done |
Stunning!!!!! ![]() ![]() ![]() Who did your zinc and cad plating on the hardware? |
Page 1 of 4 | All times are UTC - 5 hours |
Powered by phpBB® Forum Software © phpBB Group http://www.phpbb.com/ |