Kawi2strokes.com Forum
http://www.kawi2strokes.com/forum/

I started to reassemble the H1D I'm restoring. It's done
http://www.kawi2strokes.com/forum/viewtopic.php?f=13&t=12026
Page 1 of 4

Author:  GUTS [ Thu Aug 18, 2016 12:34 pm ]
Post subject:  I started to reassemble the H1D I'm restoring. It's done

This bike was not in the best of shape when I got it from Leroy. I had to resort to some cave-man tactics to get the cylinders off but all is good now. This is the first time I got the chrome back before I needed it and it only took three weeks to get it back! :thumbup: , wouldn't you know, I didn't open the box of chrome when it was delivered, I waited two weeks :oops: and when I did open it the other day I found that two of the exhaust pipes were damaged during shipping(lesson learned about unpacking stuff in front of the driver)and I had to send them back. :thumbdown: So far the bike is coming along nicely and if all goes well I should have all the parts and have it done in another two weeks.

They always look nicer than they are when you start.
Image
Getting the cylinders off.
Image
I tried less invasive means but was thwarted.
Image
Image
Image
The crank was rusted in and had to be junked. It took a whole day to get the cased apart.
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image

Author:  rngdng [ Thu Aug 18, 2016 1:47 pm ]
Post subject:  Re: I started to reassemble the H1D I'm restoring

That crank was toast. Nasty!!!



Lane

Author:  900SL [ Thu Aug 18, 2016 1:59 pm ]
Post subject:  Re: I started to reassemble the H1D I'm restoring

Wow what a job.
Looks like that engine has been sitting for quite some time!

Love the looks of the H1D, and nice looking Zed in the background btw.

Good luck !

Author:  Dewman418 [ Thu Aug 18, 2016 10:57 pm ]
Post subject:  Re: I started to reassemble the H1D I'm restoring

Looking good :thumbup:

Author:  GUTS [ Sat Oct 08, 2016 8:50 pm ]
Post subject:  Re: I started to reassemble the H1D I'm restoring. It's d

I still have the fuel line clamps and the rear footrest pins to put on but I lost them in the garage.
Image
Image
Image
Image
Image
Image
Image
Image
The cables have all since been routed correctly.
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
I'm pretty sure the master cylinder cap is from a '72 unless the early '73s had this cap. I am getting the other style ready.
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
Image
I am also still going to change out the seat cover, then it should be pretty good.

Author:  Tim Steele [ Sat Oct 08, 2016 9:01 pm ]
Post subject:  Re: I started to reassemble the H1D I'm restoring. It's done

Beautiful work!!!

Author:  67lotus49 [ Sat Oct 08, 2016 9:57 pm ]
Post subject:  Re: I started to reassemble the H1D I'm restoring. It's done

Looks super nice :thumbup:

Author:  husson73 [ Sun Oct 09, 2016 5:34 am ]
Post subject:  Re: I started to reassemble the H1D I'm restoring. It's done

Awesome job :thumbup:

Author:  mraxl [ Sun Oct 09, 2016 7:24 am ]
Post subject:  Re: I started to reassemble the H1D I'm restoring. It's done

Super nice job!
You are correct... the MCyl cap used is from earlier models.
If you aren't aware... the dash light panel is a Japan only for later models. The H1D is unique to H1 & S for '73.
Here is H1D panel:
Image

Author:  wavehog33 [ Sun Oct 09, 2016 7:48 am ]
Post subject:  Re: I started to reassemble the H1D I'm restoring. It's done

Stunning!!!!!
:clap: :clap: :clap:
Who did your zinc and cad plating on the hardware?

Page 1 of 4 All times are UTC - 5 hours
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/